Router Solution
  ------------------------------------------
Overview
Pro Series Router
Industrial Series Router
Pro Series Network Card
Ind Series Network Card
  - PCI LAN Adapters
  - PCI 431-TE Adapter
  - PCI 520 Series
  - PCI 530 Series
  - PCI 600 Series
  - PCI 720 Series
  - PCI 800 Series
  - PCI 921-CDS
  - PCI 1000 Series
  - PCI 1104-03
   
  WAN Monitoring
  ------------------------------------------
WAN monitoring card
WAN monitoring tapper
   
  Technical Support
  ------------------------------------------
Manual Downloads
Technology
Case Study
Technical Notes
FAQ
   

 

 

 

 

 

 
ImageStream Internet Solution - Inductrial Series Network Card - PCI 530


PCI 530 Series

ImageStream's PCI 530 series network cards are low-cost PCI 2.1 compliant network adapters that support multiport T1/E1/J1 or DS3/E3 connectivity for WAN and Internet routing applications. The software included with ImageStream's router distribution is used to configure each of the soft-set interfaces.

530 series WAN adapters support full or fractional line speeds independently for each port. The T1/E1/J1 cards also support DS0 multiplexing, as well as drop-and-insert with the 2 and 4 port versions. The DS3/E3 cards support full or fractional line speeds configurable in DS1 (1.5 Mbps) increments.

The 530 series T1/E1/J1 cards use a fully integrated design based on the PMC Comet and Altera chipsets. The 530 series DS3/E3 cards use the high-performance Intel 21143 chipset that supports duplex E3 speeds up to 34 Mbps per port and DS3 speeds up to 45 Mbps per port, with a maximum aggregate throughput of 180 Mbps.

The 530 series hardware supports bisync and SDLC/HDLC protocols with a low-latency PCI interface that can burst into host memory at speeds up to 256 MBps. 530 series cards provide a PCI bus interface that is compatible with 3.3 and 5 volt signaling systems. The T1/E1/J1 cards include a 32-bit 33 MHz PCI bus interface, and the DS3/E3 cards provide a 32-bit 33/66 MHz PCI bus interface.


Performance:
  • Low-latency PCI bus master
  • T1/E1/J1: 32-bit 33 MHz PCI
  • DS3/E3: 32-bit 33/66 MHz PCI
  • T1/E1/J1: Up to 4 ports, 16 Mbps aggregate throughput
  • DS3/E3: Up to 2 ports, 180 Mbps aggregate throughput
Technical Highlights:
  • Up to 4 full duplex T1/E1/J1 ports
  • Up to 2 full duplex DS3/E3 ports
  • PCI 2.1 compliant
  • 3.3 and 5 V compatible signaling
  • Short PCI form factor
  • MTBF of at least 100,000 hours
Interface Options:
  • Single, dual or quad T1/E1/J1 ports
  • Single or dual DS3/E3 ports
Environmental Requirements:
  • Operating temperature -5 to 55 degrees C (23 to 131 degrees F)
  • Relative humidity 5 to 90% (non-condensing)
Power Requirements:
  • 500 milliamps @ 5 volts (max)
 

T1 Interface Specifications:

  • D4 (SF) and ESF framing
  • B8ZS and AMI line coding
  • ANSI T1.403, AT&T 54016 and 62411 compliant
  • Test and loopback features including master & slave clocking
  • RJ48 connectors
E1 Interface Specifications:
  • AMI and HDB3 line coding
  • ITU G.703 (120 ohm), G.704, G.706, G.962
  • Test and loopback features including master & slave clocking
DS3 Interface Specifications:
  • ANSI T1.107-1195
  • ANSI T1.404-1994
E3 Interface Specifications:
  • ITU G.703 (75 ohm)
  • ITU G.751
Certification:
  • FCC Part 15 (Class A)
  • FCC Part 68
  • UL 1950, Listed Accessory
  • CISPR22 (TUV Rhineland)
  • UL Safety
  • CS003
  • DOC Canada
  • CS03
  • EN 50082-1, EN 55022, EN 41003
Model Numbers and Interface Configurations:
  • 531-TEJ - One T1/E1/J1 CSU/DSU interface
  • 532-TEJ - Two T1/E1/J1 CSU/DSU interfaces
  • 534-TEJ - Four T1/E1/J1 CSU/DSU interfaces
  • 531-DE - One DS3/E3 CSU/DSU interface
  • 532-DE - Two DS3/E3 CSU/DSU interfaces
  • 800072 - External DS3 monitoring tap
  • 800073 - External E3 monitoring tap

Top